First, Jetta remote control matching This article refers to the address: http:// Second, Shanghai Buick remote control can not be mixed, but the matching method is the same. Third, Hainan Mazda remote control matching Fourth, Chery QQ remote control matching method 1. Within 7 seconds, the ignition switch is set to ON for three times, and the third time after setting the ON position, observe the anti-theft indicator 2. After the anti-theft indicator flashes for 3 seconds, it will pause for 1 second, then the anti-theft The indicator light will light up again. When the anti-theft indicator light is off, turn the ignition switch off. 3. At this point, turn the ignition switch to the ON position, and then press any of the remote control buttons. When pressed, the anti-theft indicator will light up, indicating that The remote control has been set in the system; (1) Unplug the buzzer (Fulica is behind the glove box) 3, one-piece (key and remote control integrated) only one button (1) first unplug the buzzer plug, then unplug the receiver plug, the entire door is closed, connected to the receiver plug, to be controlled in the middle of the work ; 4, one-piece (key and remote control integrated) has two buttons: Thirteen, Audi A6 central door lock remote control transmitter matching method Fourteen, Guangzhou Honda car remote control reset program remote radio transmitter code input method is as follows: Fifteen, Passat B5 anti-theft device matching how to regain the password If you match the ignition switch key, do not know the 4-digit password, or the password card is lost, you can get the password according to the following method: connect FCAR diagnostic instrument, turn on the ignition switch, enter the address Word 25, press the Q key to confirm. After about 5s, the screen displays: 12V Adapter,Power Supply Adapter,Laptop Power Ac Adapters,Linear Desktop Power Adapter Ninghai Yingjiao Electrical Co., Ltd. , https://www.yingjiaoadapter.com
1. The setting of the first remote control key.
(1) The remote control key to be set will turn the ignition switch on/off 3 times to activate the remote control matching program.
(2) Press and hold any key on the remote control key (press and hold).
(3) Press another button 3 times within 10s.
(4) Release all buttons.
(5) The led light of the remote control key will flash 5 times.
(6) The setting work of the first remote control key is completed.
2.: The setting of the first remote control key.
When setting the second remote control key, repeat steps 2-5 in (1).
Precautions:
1) It is not necessary to activate the remote matching program when setting the second remote control key. It should be set within 20s after the first remote key setting is completed.
2) Perform initial test or turn-on ignition again
Shanghai Buick remote control match: Shanghai Buick car is equipped with remote control door lock system. The system has the function of locking the door, unlocking the door and opening the rear compartment. The remote control door lock system with alarm function also makes the horn sound and makes the car inside. The function of turning on the light and turning on the headlights of the vehicle. The remote door lock system consists of a remote transmitter and receiver. The remote door lock receiver is located on the dashboard and is powered by the vehicle battery through the instrument harness. The remote door lock receiver determines the command being transmitted by the remote transmitter and sends the signal to the body control module (BCM). The body of the remote control door lock is a 3V lithium battery driven hand control device. The transmitter's operating range is 1-9M.
When the remote control replaces the battery, or when the transmitter is out of range, the transmitter is activated more than 256 times, causing the transmitter to be out of sync. The method of resynchronization is to simultaneously press the "unlock" and "lock" buttons of the transmitter and keep at least 7S, or wait until the horn sounds 3 times.
If a remote transmitter is lost and a new remote is required, it needs to be programmed (to let the receiver know the new remote transmitter). This can be done using a scanning tool or without tools. In the absence of tools, the transmitter's programming steps are as follows:
1. Sitting on the driver's seat of the vehicle;
2. Pull the ignition switch start key out of the ignition core;
3. Close all doors;
4. Press and hold the "unlock" button on the door lock switch;
5. Keep the door lock switch in the "unlocked" position, insert and pull out the ignition start key twice. Do not turn the lock cylinder.
6. When inserting the ignition start key for the third time, keep the key in the ignition core. In the remaining procedures, the sinister device must remain in the LOCK position;
7. Release the door lock switch. You will hear three beeps. This ringing feedback indicates that the transmitter programming is starting.
8. Press the “Unlock†and “Lock†buttons on the remote door lock transmitter simultaneously for 12s. I heard two beeps. Indicates that remote programming has been successful.
9. Repeat steps for other transmitters (up to 4).
10. Pull the ignition start key out of the ignition core and exit the program.
1. Hainan Mazda remote control setting 1) Close all doors.
2) Go to the OFF position and remove the key from the ignition switch.
3) Open the driving side doors and turn them off once and twice. The gear is in the N position. Step on the brakes.
4) Insert the key into the ignition switch, turn it from OFF to ON position 5 times, and take the key to see the dangerous light flashing. Press any button on the remote control within 1 minute.
Note: After the operation is completed, the first remote control is set in the system, and then the other remote control button is pressed, and another remote controller can be set in the system. Many service stations here only operate a remote control, causing another remote control to be unavailable after the code is completed. In addition, if you do not follow the prescribed procedures, the code will definitely fail. At this time, do not easily replace the remote control and the module. You should try again according to the operating procedures. Please follow the attached instructions.
Five, Picasso Senna remote control matching 1. Turn off the ignition switch 2. Turn the ignition switch on again. Press the lock button on the remote control key for a few seconds.
4. Turn off the ignition switch and remove the remote control key from the anti-theft ignition lock. Wait 20S, the setting is successful.
Six, Santana 2000 remote control matching
1. Initialization {Applicable to the new remote control, the new remote control must be initialized with the original remote control together with the receiver. If the user loses a remote control and temporarily does not have a new remote control, the original remote control should be reinitialized to disable the lost remote control.
Setting steps:
1) Turn off the ignition switch;
2) All door contact switches are opened {ie all doors are closed;
3) Ground the programming line {with a blue harness with a tab at the 22nd corner of the receiver harness connector next to the central junction box} {ground}
4) Turn on the ignition switch;
5) Turn off the ignition switch;
6) The remote control receiver enters the 60 second programming mode;
7) If the door lock is originally locked, then all the doors will be unlocked to indicate that the remote control receiver enters the programming mode;
8) Press the remote controller for any two times within 10 seconds. The interval between the two is about 2 seconds.
9) After the programming is completed, the door lock will be locked and unlocked once to confirm;
10) Repeat steps 8, 9 for the second remote transmitter;
11) Restore the programming line and the initialization ends.
2. The remote control remote control re-synchronizes with the remote control receiver. {Applicable to the original remote control remote control, after pressing 255 times continuously outside the effective remote control distance, or the power failure time is long {if the battery is replaced for a long time}, the remote control remote control It will not be synchronized with the remote control receiver. It cannot be opened and closed in the remote control and must be resynchronized}
Setting steps:
1) Press the remote control remote control to close all the doors within 30 seconds to make the door lock open.
2) Turn on the ignition switch;
3) Turn on the button once;
4) If the synchronization is successful, the door lock will be locked and opened once to confirm.
Seven, Geely free ship remote key manual matching operation method
1. Confirm that the battery in the remote control is sufficient.
2, clear the fault code (electric control system)
3. Turn the ignition switch OFF-ON 3 times in 5S and then stop at the ON position.
4. Look at the remote control indicator of the instrument panel, first flashing at 0.1S, then flashing at 1S, and then the remote control indicator lights up for 2S before proceeding to the next step.
5. Turn the ignition switch to OFF and then to ON, then press and hold any button on the remote control for more than 2S. If the speaker rings three times, the remote control will be successfully matched. If you want to match multiple buttons, press any button for more than 2S, etc. Three sounds, only up to 4
Eight, Toyota Camry 2.4 uses the accelerator pedal and brake pedal to register the ignition Toyota Camry
1. Registration of the master key 1) Insert the registered master key into the ignition switch, continuously press and release the accelerator pedal 5 times in 15 seconds, continuously press and release the brake pedal 6 times, and stop the system. Will enter the registration mode.
2) Within 10 seconds, pull the main key out of the ignition switch, insert the main key to be registered into the ignition switch, and step on and release the accelerator pedal once. At this time, the “safety light†flashes and is in the registered state. .
3) About 3 minutes or so, the additional master key is registered, the "safety light" is off, and if you want to register another secondary key, repeat step 2 within 10 seconds. However, the operation of the sub-key, the accelerator pedal is 4 times, and the brake pedal is 5 times.
Nine, Kia Maxima remote control match
1. The anti-theft system causes the oil to be cut off. The method of releasing the power failure uses the key to lock the passenger side door, and then unlocks the lock.
2, remote control reset / program completely remove the remote control function steps
(1) Use the key to open the driver's side door to unlock the anti-theft function.
(2) Insert the key to the ignition switch KEY-ON and then OFF to remove the key.
(3) Repeat step (2) three times, or open, close the driving side door three times or press/release the driving side door switch three times.
(4) At this time, the anti-theft horn will sound once, and after waiting for 15 seconds, it will be activated four times and the anti-theft function will be cancelled.
Steps to restore remote control and reset remote transmitter:
(1) Use the key to open the driver's door.
(2) Insert the key to the ignition switch KEY-ON and then OFF, and remove the key.
(3) Repeat step (2) three times, or open and close the driver's side door three times, and press/release the driving side door switch three times.
(4) When the horn sounds, press the remote control any button twice and the horn will sound again.
(5) After waiting for 15 seconds, it will ring again four times, that is, complete the remote control reset.
(6) You can set another remote control in 15 seconds. Press any button on the new remote control twice, then it will sound once, wait 15 seconds, it will sound again four times and then reset in 15 seconds. For the third remote control, press one of the buttons on the new remote control twice, and then the sound will be twice, that is, the setting is completed.
Ten, southeast car remote control key manual matching method
1, separate type (remote control and key separation) have two buttons, red and green, no need to program in the car
2, separate type (remote control and key separation) marked with two buttons LOCK and UNLOCK
(2) The whole door is closed, it is the ECU diagnosis port No. 1 terminal grounding, the ignition switch is OFF-ON-OFF, the central locking will automatically lock and open;
(3) Press the LOCK button for 1- to 3 times within ten seconds, the central control lock will automatically lock and open, and the setting is completed;
(2) Pull the key out and pull out four times, then pull the middle hole of the left front door out and press it twice in two seconds, then the direction light will flash twice;
(3) Press the remote control's launch button for 1---4 times. At this time, the gate is unlocked and the direction light flashes once; (Other remote control must close the left door and repeat the (3) step programming, otherwise it cannot be used;
(4) Insert the key into the ignition switch, connect the buzzer plug, and the setting is completed;
(1) Connect the special tool to the host jack through a dedicated patch cord (new Delica is behind the throttle pedal);
(2) Clear password: Press the clear and learn button of the special tool at the same time;
(3) Chip password learning: turn the key to the ON position and press the learning button of the learning machine. At this time, the prompt sound can be heard and the setting is completed (if there are multiple remote controllers, this step must be repeated, otherwise it will be invalid); Control password setting: the key can't be on the ignition lock, press the learning button on the learning machine, and press any key on the key twice or more. At this time, the central control lock will act and the setting is completed (if there are multiple remote control keys to be repeated) This step, otherwise it will be invalid).
Eleven, use the car doctor to match the Polo key process
1: First enter the 17 meter system, check the instrument computer version, which has 17 bits of VIN code, 14-digit meter code starting with VW.
2, according to the last two numbers to SAIC Volkswagen to find the login password. (This password changes every day, so you must get this password through SAIC Volkswagen).
3. Return to enter 11 and enter the password obtained from SAIC Volkswagen.
4, then enter 10 (adaptive matching).
5. Enter channel number 21 (key match) and enter the number of matching keys 1-8 (up to 8). The number entered is 2, and the number of matching keys is 2.
6, the key inserted in the ignition switch is successfully matched,
7. After pulling out, insert another key to be matched, turn on the ignition switch, and the second key skin is successfully matched.
8, the next few are the same,
Twelve, A6 car remote control key adaptation method
2000 FAW Audi (C5) A6 sedan remote key adaptation method remote key reset procedure (copy remote control)
1.C5 A6 with the car usually has two remote control keys. If you want to add a remote control key, these keys must be adapted to the central door lock control unit.
2. If the fault code 00955-00958 is displayed and the remote key battery is replaced, the key should also be adapted.
Adapt to the new remote key program:
a. Turn on the ignition switch (with the secondary key);
b. In the measurement data block 007, check that several keys have been adapted;
c. Lock the driver's door lock with the car key to be fitted outside the car. Press the “offnen†button on the remote control key within 5 seconds until the next storage position is reached. Each press is approved by the alarm flash, waiting for 5 Seconds, press "offnen" again, the door opens
1. Insert one of the ignition switch start key into the ignition core KEY-ON
2. Close all the doors, insert another ignition switch start key into the driver's door lock, and lock the door with the key.
3. Pull out the ignition switch on the door lock to activate the key, press the unlock button, open the door and take out the key in the ignition core. The central door lock remote transmitter of the key is matched.
4. Re-insert another ignition switch start key into the ignition core KEY-ON
5. Repeat 6, Step 2, and Step 3 to complete the matching of the central door lock remote transmitter of another ignition switch activation key.
A simpler one is to lock the door with a key, press and hold any key on the remote control. Keep the lock or open, feel the door is shocked.
The remote transmitter can input 3 codes into the memory of the remote door receiver. At the input transmitter code you should note:
(1) If the fourth code is entered, the first code will be overwritten and deleted.
(2) During the operation, it must be completed within the time specified in the step description.
The steps to enter the remote control code are as follows:
(1) Turn on the ignition switch ON (II).
(2) Align the transmitter with the receiving device of the door and press the lock and open button of the transmitter within 4 s.
(3) Turn off the ignition switch within 4s.
(4) Transfer to step (5) within 4 s.
(5) Repeat step (1).
(6) Repeat step (2).
(7) Repeat step (3).
(8) Transfer to step (9) within 4 s.
(9) Repeat step (1).
(10) Repeat step (2).
(11) Repeat step (3).
(12) Transfer to step (13) within 4 s.
(13) Repeat step (1).
(14) Repeat step (2).
(15) Confirm that the sound of the door lock starter has been heard.
(16) Transfer to steps (17) to (22) within 9 s.
(17) Align the transmitter with the door receiver, enter the first code to be stored, and press the transmitter button.
(18) Confirm that the sound of the door lock starter has been heard.
(19) Align the transmitter with the door receiver, enter the second code to be stored, and press the transmitter button.
(20) Confirm that the sound of the door lock starter has been heard.
(21) Align the transmitter with the door receiver, enter the third code to be stored, and press the transmitter button.
(22) Confirm that the sound of the door lock starter has been heard.
If you want to save another new (4th) transmitter code, return to step (1) and proceed step by step.
(23) Turn off the ignition switch and pull out the ignition key.
(24) Use the transmitter to open or lock the door and confirm that the transmitter is working properly after entering the new code.
330 953 253 IMMO VWZ6ZOTO456789 V01 →
Coding 00000 WS05C012
VWZ6ZOTO456789 is the 14-digit number of the anti-theft device control unit on the vehicle. The 14-digit anti-theft device control unit number read by the service station will be transmitted to Shanghai Volkswagen after-sales service company, and then the password will be checked by Shanghai Volkswagen after-sales service company. Telex to the repair station.
The method and steps for matching the electronic anti-theft device with the ECU matching electronic anti-theft device and the engine control unit ECU are:
1. Connect the fault detector FCAR, turn on the ignition switch, and enter the address word "17", select "Combination Instrument System", and press the Q key to confirm, the display on the display is:
BO919881 B5 Kombiinstr. VDO X06 →
Coding 00042 WS05C012
Press the "→" button and the display on the display reads:
IMMO-IDENTNR: VWZ7Z0T2000307 →
Press the "→" button again and the display on the display reads:
Rapid data transfer HELP
Select function XX
2. Enter the address word "10", select the "match" function, and press the Q key to confirm, the display on the display is:
Adaptation Q
Feed in channel number XX
3. Enter the channel number "00" and press the Q key to confirm. The display on the display is:
Adaptation Q
Erase learnt values?
4. Press the Q key to confirm and the display on the display is:
Adaptation →
Learnt values ​​have been erased
5. Press the "→" button to end the match, then enter "06", select the "End Output" function, and press the Q button to confirm, turn off the ignition switch, and the engine control unit will read in the next ignition switch. Information on the anti-theft control unit.
16, Toyota - remote control reset and copy program
1. The anti-theft main computer 9# feet will be grounded, and all the doors will be locked and then opened at the same time.
2. At this time, press any button on the remote control to remember: lock all the doors and open all the doors and travel locks will be repeated once.
3. To copy the second remote, repeat step (2).
4. Disassemble the main computer 9# foot wire, that is, complete the setting and copying process.
â—Ž LEXUS car remote control "radio frequency signal", in the SC300 and SC400 cars FM78.6, other cars are FM94.6 fixed frequency, and use the radio antenna input signal.
â—After removing the radio antenna, turn the radio on at 94.9FM or 78.6FM to hear the radio. If not, insert the key and press the button. If there is noise from the radio, it means the remote receiver. Poor control of the computer. If there is no noise, it means the key is bad.
Seventeen, Mondeo car anti-theft key copy method
1. System operation
(1) Set the ignition switch to the ON position, and make sure the clock LED is on for 3-5s.
(2) The LED lights up for about 1 minute and then flashes at an abnormal interval, indicating that the key code is not confirmed.
2. Copy key program When the system fails or you need to add or replace a key, copy the key (to initialize the remote control).
1) Two program keys (A and B) are required.
2) Insert the A key into the ignition switch.
3) Turn the ignition switch to the second position and wait for 1 second.
4) After the ignition switch is turned to the OFF position, remove the key A.
5) Insert the B key into the ignition switch within 5 s.
6) Turn the ignition switch to the second gear position and wait for 1 second.
7) Turn the ignition switch to the OFF position and remove the key B.
8) Within 10s, insert the remote control key that needs to reset the program (remote control setting) into the ignition switch; then turn the ignition switch to the second position and wait for 4s.
9) Turn the ignition switch to the OFF position and wait for 5 s.
10) Start the engine.
11) If the engine does not start and the clock LED is flashing, set the ignition switch to the ON position and wait for a minimum of 20s; then set the ignition switch to the OFF position and reset.