LED strobe refers to two concepts One is stroboscopic: the depth at which the luminous flux of the electric source fluctuates. The greater the depth of the undulation, the greater the stroboscopic depth. The second is the stroboscopic effect: the negative effect of the strobe of the electric light source on human vision. The greater the stroboscopic depth, the greater the negative effect and the more serious the hazard. The stroboscopic and stroboscopic effects are directly related to the type of electric light source and its technical performance. Different types of electric light sources with different technical performances have different stroboscopic and stroboscopic effects. Strobe is actually a stimulating perception of the eye by the illumination source. The perception of the stroboscopic light source by the human eye depends mainly on the amplitude and frequency of the brightness of the light source. The source luminance amplitude is in turn usually expressed in terms of the modulation percentage of the amplitude and its luminance value. Experiments have shown that the different frequencies of the illumination source make the threshold percentage of the stroboscopic amplitude modulation visible to the human eye. We just talked about the stroboscopic effect of LED lighting products, but many people don't know what it means. The essence of stroboscopic light source is the fluctuation of luminous flux. Under the driving of AC or pulsed direct current, the luminous flux, illuminance or brightness change with the periodic variation of the current amplitude. The human eye to the human brain produces this change. Subjective response. Usually, the flicker is divided into visible flicker and invisible flicker according to human feelings. When the frequency is greater than 100 Hz, the human eye does not feel the flicker phenomenon, but it still causes eye fatigue, headache, etc. This is the stroboscopic effect, and it is generally believed that this effect exists within 500 Hz. For this US Energy Star (ENERGYSTARlamps V1.0draft4 specifies the conditions for flicker to be met in the requirements of dimming performance, used in all lamps, as shown below: The range allowed by the source strobe is: 1. The frequency is not less than 120Hz; 2. In the frequency range of 120Hz-800Hz, F1 3. When the frequency is greater than 800 Hz, there is no requirement for F1; 4. When the frequency is uncertain, PF In addition, the compact fluorescent light output frequency needs to be 20-30KHz, or greater than 40KHz. The essence of stroboscopic light source is the instability of luminous flux. When detecting the fluctuation of the light source with time, you can test the curve of the brightness and the curve of the luminous flux or illuminance under the same conditions. ENERGYSTAR (V1.0) specifies the measurement requirements for flicker flicker: 1. Power supply and measuring instruments must meet the requirements of LM-79-08; 2. Multi-channel oscilloscope with storage function, if necessary, add attenuation probe. The sampling rate is greater than 2 kHz, and the sampling time is greater than 100 ms; 3, photometric probe, V (in) calibration, and the corresponding time needs to meet the requirements; 4. For absolute photometry: measuring the absolute value requires an integrating sphere; for relative photometry: ensuring that the detector can measure the relative light output and only accept light from the source to be measured. Before the measurement, the compact fluorescent lamp needs to be aging for 100 hours, and it needs to be preheated before measurement. LED lights do not need to be aging, the ambient temperature is 25 +/- 5 degrees. Content extension: LED solid-state lighting products are increasingly favored by the market and consumers because of their unique luminous efficiency, long life and high reliability. But at the same time, because LED response speed is fast, and it does not have the thermal inertia and afterglow effect of traditional lamps, it is deeply affected by current fluctuations. The fluctuation of current directly affects the output of luminous flux. The flashing of light source is the external manifestation of the change of luminous flux, so The flashing problem of LED lighting products has also attracted everyone's attention. On December 14, 2012, the European Union officially issued the Regulation (EU) No. 1194/2012 in its official gazette, the European Parliament and Council Directive No. 2009/125/EC on directional lights, LED lights and Implementation Rules for Ecological Design Requirements for Related Equipment. Corresponding to the European Commission Regulation (EC) No. 244/2009 issued by the European Commission on March 18, 2009, the European Parliament and Council Directive 2005/32/EC on the implementation of the ecological design requirements for non-directional household lamps, to this end, The EU has formed a complete mandatory ecological design requirement for LED lights. Start-up time and rise time are two indicators of functional requirements, which are increasingly valued by manufacturers in the industry. Editor; CQJ
USB Speaker Speakers portable mini,Portable speaker mini,Speaker for computer,Usb speaker for computer SHENZHEN HONK ELECTRONIC CO., LTD , https://www.honktech.com
This mini Portable Speaker is specially designed for Desktop, Laptop, Notebook, Tablet PC. With small body and Lightweight,this usb Computer Speaker is convenient to carry.Its high-grade loud speaker will bring you much wonderful voice when listening to music,watching film or playing games. This USB Mini Speaker will be a super companion for your daily life.
The Portable mini speaker is USB-powered,plug and play,very easy.The mini sound box speaker is built-in volume control, very convenient to adjust volume. The Desktop Speaker is energy-saving and environmentally-friendly.It is safe and reliable.
